2003FL-Low Flow Blender w/ Flow Meter and Bleed Control
The 2003FL features a close mounted 0-15 lpm flow meter on the left side that keeps the footprint of this blender much smaller than a flow meter installed on a traditional blender with a DISS fitting. The bleed control knob on the right side allows for gas savings when flows are used at flows higher than 3 lpm (or when not in use) by disabling the bleed flow. When precise accuracy below 3 lpm is needed, bleed flow can be enabled. It also features a bottom DISS port.
|Height||6.64" (16.9 cm)|
|Width||5.48" (13.9 cm)|
|Depth||4.56" (11.6 cm)|
|Weight||2.79 lbs (1.27 kg)|
Part Number: 2003FL
Flow Range: 0 to 30 LPM
Input Port Fittings: DISS (for NIST add Part # 2007)
to your order Output Port Fittings: DISS
Output Port Flow Range:
Left – 0-15 LPM Flowmeter (green O2 label) Bottom – 3-30 LPM (no bleed)
0-30 LPM (with bleed) Right – Knob to switch bleed on & off
Bleed for Flows <3 LPM: 3 LPM Size: 5.6W x 6.7H x 4.6D inches
|Oxygen Concentration Range||21-100%|
|Number of Ports||2|
|Flowmeter Range||3-15 lpm (with bleed flow off), 1-15 lpm (with bleed flow on)|
|Accuracy||+/- 3% full scale|
|Bleed Flow||3 lpm (when active)|
- Hose Kits (2', 3' or 10' long)
- Brackets (Wall Mount, Pole Mount, or virtually any rail or headwall configuration)
- Quick Connect Fittings (Hose kits are configured with DISS fittings...Ohmeda Style and Chemtron Quick Connect fittings are also available)
The Sentinel Kit is an oxygen analyzer (with alarms) that can be connected to an air/oxygen blender. The kit comes with a bracket that positions the analyzer on top of the blender. The analyzer port assembly connects the bottom port of a Bio-Med Devices or Bird blender.and as such does not require a flowmeter dedicated to this task. It can be purchased for existing blenders or along with new blenders.
The 2016 is a dual flowmeter attachment that was created initially as a means to add flowmeters to the Crossvent 2i+ infant transport vent. The 0-8 lpm flow meter provides adequate flow to connect a resuscitation bag to (in case it is needed during transport). The low flow 0-4 has very low flow increments that start at 1/32 lpm, and also 1/16, 1/8, 1/4, etc.
The 2016 can also be added to blender models that have a bottom port, such as the 2003FL (which would provide a 0-15, 0-8 and 0-4 lpm flowmeter), and will keep the wall space required, to a minimum.
Hose kit includes a 10' long air hose with female DISS air connections on each end, a 10' long oxygen hose with female DISS connections on each end, and a male-to-male DISS oxygen connector that converts the female oxygen supply input on blender to a male fitting
The 15' dual coiled air/oxygen hoses are ideal for connecting any equipment that must be connected to both an air and oxygen gas source (ventilators, air/oxygen blenders, CPAP devices, high flow cannula devices)
- The coiled nature of the hoses makes them easy to stow during storage or transport (hoses stay up off the floor).
- The coiled nature of the hoses also stay up off the floor during use (no matter how close you get to the wall outlet).
- This does not create a tripping hazard as traditional hoses can.
- Since the hoses are fused together except for the ends, they don't get tangled with one another.
Note: If you are ordering this hose for a blender application, make sure you order the PFIT150 (male-to-male DISS fitting) so the oxygen hose will connect to the oxygen input on the blender.
This male-to-male DISS fitting is used in our blender hose kits to convert the oxygen female input port on our blenders to a male DISS port. If you are contemplating hoses from another source, you may want to have the oxygen input configured with a male fitting, or purchase this fitting separately. If you choose to use the 15' dual coiled hose for your blender, you would want to purchase this item so it would connect appropriately.
This regulator offers several nice features including a built-in o-ring tank washer, built-in protected gauge, and 0-15 lpm flow meter, but the best and most unique feature of all is its ability to be connected to the wall source at the same time as the tank source (via a 50 psi input DISS connection), which allows for a seamless transition from one gas source to the next. It also doesn't cause loud blender alarms when switching over or cause wild swings in oxygen percentage from 21% to 100% or vice versa.