Crossvent 3+ Pediatric - Adult Ventilator
You can order the Crossvent 3+ in any one of three configurations: Standard, with Bio-Med Devices Air/Oxygen Blender attached or with air entrainment. The attached blender allows the user to set oxygen concentration from 21% to 100%. Units with air entrainment can deliver either 100% oxygen or a nominal 50% oxygen without the need for an external air supply source. The unique venturi mechanism built into the unit increases oxygen tank life by mixing ambient air with the source oxygen.
The Crossvent 3+ can be powered by a compressor, blended gas or 100% oxygen, and its consumption of gas is extremely low. The internal battery provides power in the event of AC power failure. If the external power should fail, the unit will automatically switch to its battery power and sound an alarm. A fully charged battery will last approximately 6 hours.
Available alarms include exhaled tidal volume, PIP, PEEP, mean pressure, low supply pressure, rate, oxygen concentration and low battery.
Highlights of enhancements include:
Color display with greater visibility and viewing angle
Improved touchscreen sensitivity
Improved battery gauge providing greater accuracy in 2% increments
Optional Exhaled Vt
Optional Exhaled VE
Key features include:
Ultra-compact and lightweight design
Unmatched gas efficiency
Long battery life
Multiple Ventilation modes
LED power indicator
Foolproof circuit connections
Air and ground transport
Intra or inter-hospital transport
Intensive care unit
|Height||10 inches (25.4 cm)|
|Width||11 inches (28.0 cm) or 13.5 inches (34.3 cm) with optional mounted blender|
|Depth||5.5 inches (14cm)|
|Weight||10.5 lbs (4.8 kg) or 13.5 lbs (6.1kg) with optional mounted blender|
3300C Basic Crossvent 3+
3300AC Crossvent 3+ with Air Entrainment
3300BC Crossvent 3+ with attached Air/Oxygen Blender
3300EC Crossvent 3+ with Exhaled Tidal Volume Monitoring
3300AEC Crossvent 3+ with Exhaled Tidal Volume Monitoring and Air Entrainment
3300BEC Crossvent 3+ with Exhaled Tidal Volume Monitoring and attached Air/Oxygen Blender
All models include a Disposable Adult Circuit, O2 High Pressure Supply Hose, Oxygen Sensor Cell with Cable, Adult Test Lung, External Power Supply and Instruction/Service Manual.
Heavy Duty Stand (includes tilt bracket), Filter Water Trap (Air), Filter Water Trap (o2), Pediatric Adult Pneumotach, Standard Pole Mount Bracket, Circuit Support Arm, Support Arm Bracket, Blender Pole Bracket, Disposable Pediatric Circuit, Reusable Adult Circuit
Blender or Air Entrainment
Exhaled Tidal Volume
Exhaled Minute Volume
|Tidal Volume||5-2500 ml|
|Inspiratory Time||0.10 - 3.0 seconds|
|Flow Rate||1-120 lpm|
|Peak Pressure||0-120 cmH2O|
|PEEP Pressure||0-35 cmH2O|
|Pressure Trigger||-.2 to -10 cmH2O|
|Pressure Support||0-50 cmH2O|
|SIMV Rate||0.6 - 50 bpm|
|I/E Ratio||3:1 to 1:99|
This regulator offers several nice features including a built-in o-ring tank washer, built-in protected gauge, and 0-15 lpm flow meter, but the best and most unique feature of all is its ability to be connected to the wall source at the same time as the tank source (via a 50 psi input DISS connection), which allows for a seamless transition from one gas source to the next. It also doesn't cause loud blender alarms when switching over or cause wild swings in oxygen percentage from 21% to 100% or vice versa.
This stand has an integrated swivel bracket at the top that can be configured for either a blender or a Crossvent.
Note: This bracket set will hold a sungle e-cylinder to the Deluxe stand. It includes an upper and lower section to secure the tank. In order to secure two tanks to the stand, two sets would need to be purchased.
The 15' coiled oxygen hose is ideal for connecting ventilators that only need an oxygen source to power them (like the TV-100 or a Crossvent model configured with the air entrainment feature).
- The coiled nature of the hose makes it easy to stow during storage or transport (the hose stays up off the floor).
- This hose will also stay up off the floor during use (no matter how close you get to the oxygen source).
- This does not create a tripping hazard as a traditional hose can.
- The 15’ length provides 50% more reach than our standard 10’ hose.
This bracket is used in conjunction with the support arm #2013SAH and attaches to either of our stands.
The support arm is used with the support arm bracket (Part #2013SH) for those that choose to add a support arm to their stand.
The 15' dual coiled air/oxygen hoses are ideal for connecting any equipment that must be connected to both an air and oxygen gas source (ventilators, air/oxygen blenders, CPAP devices, high flow cannula devices)
- The coiled nature of the hoses makes them easy to stow during storage or transport (hoses stay up off the floor).
- The coiled nature of the hoses also stay up off the floor during use (no matter how close you get to the wall outlet).
- This does not create a tripping hazard as traditional hoses can.
- Since the hoses are fused together except for the ends, they don't get tangled with one another.
Note: If you are ordering this hose for a blender application, make sure you order the PFIT150 (male-to-male DISS fitting) so the oxygen hose will connect to the oxygen input on the blender.