Transport Ventilators   |   Air/Oxygen Blenders   |   MRI Ventilators

Any Questions? +1-800-224-6633

Crossvent 2i+ Built-In Infant Ventilator

The built-in version of the Crossvent 2i+ is most often purchased as a part of the complete transport incubator provided by several different companies. However, in cases where an older infant transport ventilator such as the MVP-10 or the monochrome screen original Crossvent 2i are built-in, the Crossvent 2i+ can be purchased so as to upgrade the older ventilator.

Features

The Crossvent 2i+ Built-in infant ventilator features patient-triggered ventilation using a proximal flow sensor sensitive enough to allow the smallest of patients to trigger the vent. The flow sensor (pneumotach) also accurately measures the patient's exhaled tidal volume down to 2.0 ml. The built-in rechargeable nickel-metal hydride battery provides at least 3 hours of run time on a full charge (back light can also be dimmed to greatly extend this battery life). The vent features a touch screen display that is visible under all lighting conditions, and a full complement of alarm parameters.

Ventilation Modes

Pulsatile/Constant Flow
Assist Control
SIMV
CPAP
Pressure Support
Flow Trigger

Dimensions & Weight
Height 7.5" (19.1cm)
Width 8.4" (21.3cm)
Depth 4.4" (11.2 cm)
Weight 7.65lbs (3.5kg)


Ordering Information

2200JC    This model is designed to replace the MVP-10 that is built into a transport incubator made by Airborne Life Support
2200IC     This model is designed to replace a monochrome screen version of the the Crossvent 2i that was previously built into a transport incubator made by Airborne Life Support
NOTE: It is strongly recommended that in addition, the MKIT005 is also ordered with both models above (This kit provides fresh tubing and an oxygen tee that is configured correctly for a secure connection of all tubing from the rear of the vent to the remote fittings on the side wall of the incubator.

2200HC   This model is designed to replace an MVP-10 that was built into a Globetrotter TI-500 transport incubator made by Draeger (previously mad by Hill-Rom/Airshields  (this model comes with the installation kit that is specific to this version of incubator)

 
Specifications
Rate 5-150
Tidal Volume 5-750
Inspiratory Time 0.10 - 3.0 seconds
Flow Rate 1-15 lpm
Peak Pressure 0-80 cmH2O
PEEP 0-20 cmH2O
Flow Trigger 0-20 (sensitivity scale)
Base Flow 2.5 lpm
Pressure Support 0-50 cmH2O
SIMV Rate 0.6 - 50 bpm
Continuous Flow 0-15 lpm
Pneumatic Power Source 17-55 psi (117-380 kPa)
O2 Sensor 21-100%

 

Optional Accessories

Chemtron Style Oxygen Quick Connect Fitting Chemtron Style Oxygen Quick Connect Fitting
P/N: 1044
Chemtron Style Air Quick Connect Fitting Chemtron Style Air Quick Connect Fitting
P/N: 1045
Deluxe Oxygen E-Cylinder Regulator Deluxe Oxygen E-Cylinder Regulator
P/N: 1005M
» Learn More Brochure Download

This regulator offers several nice features including a built-in o-ring tank washer, built-in protected gauge, and 0-15 lpm flow meter, but the best and most unique feature of all is its ability to be connected to the wall source at the same time as the tank source (via a 50 psi input DISS connection), which allows for a seamless transition from one gas source to the next. It also doesn't cause loud blender alarms when switching over or cause wild swings in oxygen percentage from 21% to 100% or vice versa.

Deluxe Air E-Cylinder Regulator Deluxe Air E-Cylinder Regulator
P/N: 1006M
Brochure Download
Infant Test Lung (10/case) Infant Test Lung (10/case)
P/N: 1021
15' Dual Coiled Air/Oxygen Hose 15' Dual Coiled Air/Oxygen Hose
P/N: 1013
» Learn More

The 15' dual coiled air/oxygen hoses are ideal for connecting any equipment that must be connected to both an air and oxygen gas source (ventilators, air/oxygen blenders, CPAP devices, high flow cannula devices)

  • The coiled nature of the hoses makes them easy to stow during storage or transport (hoses stay up off the floor).
  • The coiled nature of the hoses also stay up off the floor during use (no matter how close you get to the wall outlet).
    • This does not create a tripping hazard as traditional hoses can.
  • Since the hoses are fused together except for the ends, they don't get tangled with one another.

Note: If you are ordering this hose for a blender application, make sure you order the PFIT150 (male-to-male DISS fitting) so the oxygen hose will connect to the oxygen input on the blender.

Ohmeda Style Quick Connect Oxygen Fitting Ohmeda Style Quick Connect Oxygen Fitting
P/N: 1042
Ohmeda Style Quick Connect Air Fitting Ohmeda Style Quick Connect Air Fitting
P/N: 1043